Daikin J Series Service Manual Page 278
- Page / 344
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SiE18-201 For BPMK928B42 · 43
Removal Procedure 267
4
Heat up the brazed
sections of the
motorized valve. Using
pliers or the like,
disconnect the valve.
Reassembling precautions
1. Use non-oxidizing brazing
method. If nitrogen gas is not
available, braze the parts
speedily.
2. Avoid deterioration of the
packings due to
carbonization of oil inside the
motorized valve or thermal
influence. For this purpose,
wrap the motorized valve
with wet cloth and splash
water over the cloth against
becoming too hot (keep it
below 120˚C).
In pulling the pipes, be
careful not to overtighten
them with pliers. The pipes
may get deformed.
The strainer is located inside
each motorized valve. When
replacing the motorized
valve, be sure to change its
strainer too. (Otherwise the
strainer will get burnt and out
of function.)
Using the outdoor liquid gas
shut-off valve, open the
indoor line.
If the gas welding machine fails
to remove the motorized valve,
take the steps below.
1. Disconnect the brazed pipe
sections that are readily
easy to separate and join
together later.
2. With a small copper tube
cutter, cut off the internal
pipes to easily take out the
motorized valve.
Note:
Never use a hack saw. Cuttings
may come into the pipes.
Step Procedure Points
Strainer
(M1130)
- J Series 1
- Super Multi Plus 2
- SiE18-201 3
- Table of Contents iii 4
- Table of Contents v 6
- 1. Introduction 8
- 1.1.3 Inspection after Repair 10
- 1.1.4 Using Icons 11
- 1.1.5 Using Icons List 11
- List of Function 12
- 1. List of Function 13
- SiE18-201 List of Function 14
- List of Function 3 14
- List of Function SiE18-201 15
- 4 List of Function 15
- 1 : for FLK, FLX50/60J 15
- : for FLK, FLX50/60J 15
- List of Function 5 16
- 1 : for FLX50/60J 16
- : for FLX50/60J 16
- 6 List of Function 17
- Specifications 18
- 1. Specifications 19
- Outdoor Unit 20
- Main Piping 20
- Branch Piping 20
- Indoor Unit 20
- 1.1.2 Heat Pump 23
- 1.2 BP Units 27
- 1.3 Indoor Units (for Europe) 28
- 5.0kW Class · 6.0kW Class 29
- 7.1kW Class 29
- Duct Connected Type 30
- 2.5kW Class · 3.5kW Class 31
- Floor Standing Type 33
- Printed Circuit Board 34
- Connector Wiring Diagram 34
- Name of Connector 35
- Other Designations 35
- Printed Circuit 35
- Board (1) 37
- (Control PCB) 37
- FVX25 / 35K Series 39
- Printed Circuit Board (1)~(3) 40
- 1.4 FTXD50~71JV Series 41
- Other Designation 45
- Main Functions 48
- 1. Main Functions 49
- For FTX25/35 J 50
- For FTK(X)25/35 J 51
- Detailed 52
- room temperature is at 53
- 1.1.15 Intelligent Eye 54
- Series Only 55
- Processing 55
- 1.1.17 Program Dry Operation 56
- Differential 57
- Compressor ON 57
- Compressor OFF 57
- 1.1.20 Auto-Restart Function 58
- 1.1.22 Auto-Swing of Flap(s) 58
- Main Functions SiE18-201 59
- 48 Main Functions 59
- BLADE ANGLE 59
- 1.1.26 Powerful Operation 60
- 1.1.27 Filter Check Indicator 61
- 1.2 SkyAir 62
- 52 Main Functions 63
- The Corresponding Models 64
- Cautions 64
- 54 Main Functions 65
- OutdoorUnit / BP Unit 66
- 56 Main Functions 67
- Parts of Outdoor Unit 68
- 1.2 Major Functional Parts 69
- Main Functions 59 70
- 60 Main Functions 71
- 2. Protection Device 72
- 2.2 BP Unit 73
- 3. System control 74
- 3.2 Mode Configuration 75
- Explanation of 76
- The Function 76
- Standby Operation 77
- 3.5 Equalizing Control 78
- Equalizing Control in Heating 79
- Main Functions 71 82
- 3.7 Oil Return Operation 85
- Main Functions 75 86
- 3.8 Defrost Operation 87
- Heating standby operation 88
- Cooling standby operation 88
- 3.10 Equalizing Control 89
- Equalizing control in heating 90
- 3.11 Capacity Control 91
- Main Functions 81 92
- 3.12 Peak Cut Control 93
- 3.13 Freeze-Up Prevention 94
- 3.14 Gas Shortage Malfunction 95
- 3.15 Discharge Pipe Control 96
- 3.16 Input Current Control 97
- 88 Main Functions 99
- 3.17 Wet Protection Control I 100
- Temperature Control 101
- SiE18-201 System control 102
- Main Functions 91 102
- Purpose of the 104
- Function 104
- 3.22 PI Control 105
- 3.23 Warm-Up Function 106
- 3.25 Fan Control 108
- 3.25.2 Fan OFF Delay Control 109
- Main Functions 99 110
- EVG: Gas pipe motorized valve 110
- Main Functions 101 112
- System control SiE18-201 113
- 102 Main Functions 113
- Temperature 114
- Main Functions 105 116
- Main Functions 107 118
- 112 Main Functions 123
- 114 Main Functions 125
- Pipe Temperature 130
- 3.37 4-Way Valve Operation 131
- 3.38 JIS Mode 132
- 3.39 Pump Down Operation 133
- SkyAir Indoor 134
- Unit Peak-Cut 134
- 124 Main Functions 135
- Flow of Refrigerant 136
- 1. Flow of Refrigerant 137
- SiE18-201 Flow of Refrigerant 138
- Flow of Refrigerant 127 138
- Flow of Refrigerant SiE18-201 139
- 128 Flow of Refrigerant 139
- Flow of Refrigerant 129 140
- 130 Flow of Refrigerant 141
- Flow of Refrigerant 131 142
- (Cooling) 143
- Refrigerant) 144
- (2.5 kW) (Cooling) 146
- 136 Flow of Refrigerant 147
- Flow of Refrigerant 137 148
- 138 Flow of Refrigerant 149
- 1.14 Defrost Operation 150
- 140 Flow of Refrigerant 151
- (Heating) 152
- 142 Flow of Refrigerant 153
- (2.5 kW) (Heating) 155
- Operations 156
- 1. Remote Controller 157
- 1.1.2 FVX25 / 35KZ 158
- 1.1.3 FTXD25 / 35KZ 159
- 1.1.4 FTXD50 / 60 / 71J 160
- 1.1.5 FLX50 / 60J 161
- 1.1.6 CDX25 / 35 / 50 / 60J 162
- 1.1.7 CDX25 / 35 / 50 / 60HA 163
- 1.1.8 FLX25 / 35H 164
- BRC7C513WC 165
- NAMES AND FUNCTIONS OF THE 166
- OPERATING SECTION (Fig. 1, 2) 166
- 1.2 Wired Remote Controller 167
- Operating Test 168
- 1. Operating Test 169
- SiE18-201 Operating Test 170
- Operating Test 159 170
- INITIALIZE SETTING 171
- TEST OPERATION SWITCH [SW7] 172
- Digital display: 173
- "" 173
- 1 SYSTEM LAYOUT 174
- 2. Method of Field Set 175
- Wireless Remote Controller 176
- 2.1.2 Local Setting Mode No 177
- Air Flow Direction Setting 178
- Setting Table 178
- Filter Sign Setting 178
- Explanation 179
- Setting the 179
- Receiver 179
- <KRP928A1S> 183
- 7. Settings 184
- SiE18-201 Method of Field Set 184
- Operating Test 173 184
- 6. Function 184
- Applicable model series 185
- These cases are not troubles 185
- Service Diagnosis 186
- Indicator lamps 187
- Operation lamp (green) 187
- Air outlet 187
- Troubleshooting 188
- Indication 188
- 1.2 Service Check Function 189
- 1.4 Troubleshooting 191
- 1.5 Troubleshooting Detail 192
- 5 B 5 193
- C4, C5, C9, CA 196
- 1.5.5 Faulty Indoor Unit PCB 197
- 1.5.6 Faulty Indoor Unit PCB 198
- 188 Service Diagnosis 199
- CDK(X)25~60H) 200
- 5 B 3 203
- Controller) 204
- Service Diagnosis 195 206
- 196 Service Diagnosis 207
- " UP " button 208
- " DOWN " button 208
- 198 Service Diagnosis 209
- General 210
- Precautions 210
- Maintenance 210
- 2.5.1 Explanation for Symbols 211
- 2.6 Troubleshooting Detail 212
- 202 Service Diagnosis 213
- 204 Service Diagnosis 215
- Service Diagnosis 205 216
- 206 Service Diagnosis 217
- Supposed 220
- Switch Box 222
- Service Monitor 222
- 3.3 Troubleshooting Detail 223
- 3.3.2 Compressor Lock 224
- 3.3.3 Fan Lock / Overcurrent 225
- Service Diagnosis 215 226
- 216 Service Diagnosis 227
- Service Diagnosis 217 228
- 3.3.7 LP Drop Error 229
- Faulty high pressure switch 230
- 220 Service Diagnosis 231
- Service Diagnosis 221 232
- 222 Service Diagnosis 233
- 3.3.19 Abnormal LP Error 241
- Service Diagnosis 231 242
- 232 Service Diagnosis 243
- Service Diagnosis 233 244
- Service Diagnosis 235 246
- 3.3.24 Electronic Thermal 247
- 3.3.25 Stall Prevention 248
- Faulty fan PC board 249
- Service Diagnosis 239 250
- 240 Service Diagnosis 251
- 242 Service Diagnosis 253
- Service Diagnosis 243 254
- 244 Service Diagnosis 255
- 3.3.32 System Malfunction 257
- Service Diagnosis 247 258
- 3.3.34 Faulty Fin Thermistor 259
- 3.4 How to Check 260
- Check No.4 261
- In the case of RMX140JVMC 262
- Compressor's terminal 263
- (U, V, W, N) 263
- Output Current 264
- Measurement 264
- Output Voltage 264
- (R25=20kΩ, B=3950) 265
- Check No.9 266
- Check No.11 267
- Check No.12 267
- Check No.14 268
- 4. BP Unit Trouble Diagnosis 270
- 260 Service Diagnosis 271
- Removal Procedure 272
- 1. For BPMK928B42 · 43 273
- SiE18-201 For BPMK928B42 · 43 278
- Removal Procedure 267 278
- Step Procedure Points 278
- 1.4 Removal of Thermistor 279
- Removal Procedure 269 280
- 2. Outdoor Unit 281
- Electrical box 284
- Wire harness 284
- Connectors 284
- Relay connector 285
- Lock screws 285
- Filter PCB 285
- Outdoor Unit SiE18-201 289
- 278 Removal Procedure 289
- 2.4 Removal of Thermistor 292
- Motorized 293
- Putty for check valve 293
- SiE18-201 Outdoor Unit 294
- Removal Procedure 283 294
- 2.7 Removal of Compressor 297
- Lock bolt 298
- Lock nut 298
- 2.8 Removal of 4-way Valve 299
- 290 Removal Procedure 301
- 3. Indoor Unit 303
- Cautions before Operation 304
- 1. Installation 305
- SiE18-201 Installation 306
- Caution Before Operation 295 306
- INSTALLATION 307
- INSTALLATION OF THE MAIN UNIT 308
- 2. Wiring 309
- Make sure numbers 310
- 1, 2, and 3 all match 310
- CONNECTING THE WIRING 311
- Wiring SiE18-201 313
- 302 Caution Before Operation 313
- SiE18-201 Wiring 314
- Caution Before Operation 303 314
- 3. Others 315
- Others SiE18-201 317
- 306 Caution Before Operation 317
- ADDRESS SWITCH 318
- Appendix 320
- 1. Piping Diagrams 321
- 1.3 Indoor Units 323
- FLX25 / 35HV1NB 324
- Field Piping φA cut 325
- Field Piping φB cut 325
- FTXD25 / 35KZV1B 326
- FVX25 / 35KZV1B 327
- 2. Wiring Diagrams 328
- 2.2 BP Units 329
- 2.3 Indoor Units 330
- FHYB35 / 45 / 60 / 71FK7V1 331
- FTXD50 / 60 / 71JV1B 332
- FLX50 / 60JV1B 334
- Wiring Diagrams SiE18-201 335
- 324 Appendix 335
- Index iii 338
- Drawings & Flow Charts 340
- Zandvoordestraat 300 344
- B-8400 Ostend - Belgium 344
Related products and manuals for Split-system air conditioners Daikin J Series
(24 pages)
(15 pages)
(12 pages)© 2020, manymanuals.com. All rights reserved. | 0.188 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals