Daikin Quaternity H-Series Specifications download pdf (Page 27)

Installation Manual EDUS04-906_b

26 Room Air Conditioners H-Series

Installing the mounting plate.

• The mounting plate should be installed on a wall which can support the weight of the indoor unit.

1) Temporarily secure the mounting plate to the wall, make sure that the panel is completely level, and mark the boring

points on the wall.

2) Secure the mounting plate to the wall with screws.

Recommended mounting plate retention spots and Dimensions

Boring a wall hole and installing wall embedded pipe.

• For walls containing metal frame or metal board, be sure to use a wall

embedded pipe and wall cover in the feed-through hole to prevent possible

heat, electrical shock, or fire.

• Be sure to caulk the gaps around the pipes with caulking material to prevent

water leakage.

1) Bore a feed-through hole of φ2-9/16 inch (65mm) in the wall so it has a down

slope toward the outside.

2) Insert a wall pipe into the hole.

3) Insert a wall cover into wall pipe.

4) After completing refrigerant piping, wiring, and drain piping, caulk pipe hole

gap with putty.

Installing inter-unit wiring.

1) Open the front panel and remove the service lid.

2) Pull out the inter-unit wiring from the back of the

indoor unit to the front. It is easier to pull out if

bending up the wire edge in advance.

3) To connect the inter-unit wiring after hooking the unit

onto the mounting plate, connect the inter-unit

wiring as shown in the figure at right.

(Bolt size : 3/8 (M10))

6-1/2 (165) 11-3/16 (285)

5-11/16 (145)

1-3/4

(45)

9/16

(14.5)

12 (305)

1-3/4

(44.5)

10-1/4 (260.5)

1-3/4

(44.5)

1-7/16 (36.5)

5-15/16

(150)

3-15/16

(100)

15-3/16 (385)

6-11/16

(170)

11-15/16 (302.5)

21-9/16 (548)

23-9/16 (598)

5/8

(15)

35-1/16 (890)

7/16

(12)

4-3/4

(120)

Removed pipe

port cover

Mounting plate

* The removed pipe port cover can be

kept in the mounting plate pocket.

Use tape

measure

as shown.

Position the

end of a tape

measure at ∇.

Liquid pipe end

Gas pipe end

Keep here the piece cut out

from the unit for piping

Through the wall

hole φ2-9/16 (65)

Drain hose

position

Through the wall

hole φ2-9/16 (65)

Drain hose

position

φ2-9/16 (65)φ2-9/16 (65)

Place a leveler on raised tab.

Recommended

mounting plate

retention spots

(9 spots in all)

(Bolt size : 3/8 (M10))

unit : inch (mm)

Inside Outside

Caulking

Wall embedded pipe

(Field supply)

Wall hole cover

(Field supply)

Wall embedded pipe

(Field supply)

φ2-9/16 (65)

Inter-unit wiring

Hang indoor

unit’s hook here.

Lift the indoor unit slightly

by placing it on packing

or other similar materials.

When stripping the ends of

inter-unit wiring in advance,

bind right ends of wires with

insulation tape.

Pull down using caution not

to catch the inter-unit wiring.

Indoor Unit Installation

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 79 80

Comments to this Manuals

No comments

Daikin Quaternity H-Series Specifications Page 27

Comments to this Manuals

Related products and manuals for Heat pumps Daikin Quaternity H-Series