Daikin FTKS60FV1B Specifications Page 109
- Page / 355
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Control Specification SiBE12-713
98 Function and Control
3.14 Wiring-Error Check
Outline The convenient Wiring Error Check function is designed for the microcomputer to correct wiring
errors itself.
If local wiring is unclear in the case of buried piping, for example, just press the wiring error
check switch that is behind the right-hand panel of the outdoor unit. Even if the connections for
Room A and Room B are confused, the system may run without a hassle. Note that this check
function does not work in the following cases.
For about 1 minute after the power is turned on (during initial setup).
For 3-minute standby period after the compressor has stopped.
When the outdoor air temperature is below 5°C.
If the indoor unit is in trouble (also in case of all-room transmission failure).
When the piping and wiring are perfect, there is no need to use this function.
Operation 1. Remove the 2 screws from the service panel (right side panel) and detach the panel.
2. Press the wiring error check switch on the service monitor PCB, and the wiring error check
function is activated.
3. In about 10-15 minutes, the checking will end automatically.
4. When the checking is over, the service monitor LED indicators start flashing.
Self-correction complete…The LED indicators 1 ~ 4 flash one after another.
Self-correction impossible…The LED indicators flash all at the same time.
Transmission failure occurs at any of the indoor units.
The indoor unit heat exchanger thermistor is disconnected.
An indoor unit is in trouble (if a trouble occurs during the wiring error checking).
Emergency stop…Any of the LED indicators 1 ~ 4 stays on.
Note: 1. After self-correction completed, LED 3 and LED 4 are not displayed for 2 rooms, LED 4 is
not displayed for 3 rooms.
2. It takes about 10-15 minutes (after pressing the wiring error check switch) to complete the
checking. (Wrong wiring between the upper and lower units cannot be self-corrected.)
3. Wrongly connected liquid and gas pipes cannot be self-corrected either. Be sure to make the
liquid pipe and the gas pipe in pairs.
4. To forced-terminate the wiring error check procedure halfway, press the wiring error check
switch again.
In this case, the microcomputer's memory gets back to its initial status (Room A wiring
→
Port A piping, Room B wiring
→
Port B piping).
5. In replacing the outdoor unit PCB, be sure to use this function.
6. Make the power slide setting after doing the wiring error checking. (Otherwise, if the wiring is
reversed, the air-conditioners being connected are set up in the reverse way.)
Basic Knowledge
This function works in this way. Refrigerant is let flow from Port A and on. The temperatures
of the indoor unit heat exchanger thermistors are detected one by one to check up the
matching between the pipes and wiring.
With this function on, freezing (crackling) noise may be heard from the indoor unit. This is
not a problem. (This is because the heat exchange temperature is made to drop below 0°C
in order to increase the detection accuracy.)
The indoor fan is made to turn on and off at the same time.
LED 1 2 3 4 Judgment
Status
All flashing at once Self-correction impossible
Flashing one after another Self-correction complete
- F-Series 1
- SUPER MULTI NX 2
- SiBE12-713 3
- Table of Contents iii 4
- 1. Introduction 6
- 1.2 Used Icons 10
- Introduction SiBE12-713 11
- List of Functions 12
- 1. List of Functions 13
- SiBE12-713 List of Functions 14
- List of Functions 3 14
- : Holding Functions 14
- — : No Functions 14
- List of Functions SiBE12-713 15
- 4 List of Functions 15
- List of Functions 5 16
- 6 List of Functions 17
- 1.2 Heat Pump Models 18
- 8 List of Functions 19
- List of Functions 9 20
- 10 List of Functions 21
- List of Functions 11 22
- 12 List of Functions 23
- Specifications 24
- 1. Specifications 25
- SiBE12-713 Specifications 26
- Specifications 15 26
- 50Hz 230V 26
- Specifications SiBE12-713 27
- 16 Specifications 27
- Specifications 17 28
- 18 Specifications 29
- Duct Connected Type 29
- Specifications 19 30
- 20 Specifications 31
- Specifications 21 32
- Floor Standing Type 32
- 22 Specifications 33
- Ceiling-suspended Type 33
- Specifications 23 34
- 1.3 Indoor Units - Heat Pump 35
- Specifications 25 36
- 26 Specifications 37
- Specifications 27 38
- 28 Specifications 39
- Specifications 29 40
- 30 Specifications 41
- Specifications 31 42
- 32 Specifications 43
- Specifications 33 44
- Floor Standing Type 50Hz 230V 44
- 34 Specifications 45
- 1.4 Outdoor Units - Heat Pump 46
- 36 Specifications 47
- Printed Circuit Board 48
- Connector Wiring Diagram 48
- 1.1 Wall Mounted Type 49
- 1.1.2 FTK(X)S20~35C 51
- PCB(2): Signal Receiver PCB 53
- 1.1.3 FTK(X)S50~71F 54
- 1.1.4 FTXG25~35E, CTXG50E 56
- 1.2 Duct Connected Type 58
- 2P084375 59
- PCB (3): Display PCB 62
- PCB (4): Signal Receiver PCB 62
- 1.4 Floor Standing Type 63
- PCB Detail PCB(1): Sensor PCB 64
- PCB(2): Control PCB 64
- 1.5 Ceiling Suspended Type 65
- EC0606(A) 66
- 1.6 Outdoor Units 67
- PCB Detail PCB(1): Main PCB 68
- PCB(2): Service Monitor PCB 69
- Function and Control 70
- 1. Main Functions 71
- Auto-Swing 73
- SiBE12-713 Main Functions 74
- Function and Control 63 74
- Heating Cooling 74
- Main Functions SiBE12-713 75
- 64 Function and Control 75
- 1.5 Programme Dry Function 77
- 1.6 Automatic Operation 78
- 1.7 Thermostat Control 79
- 1.8 Night Set Mode 80
- 1.9 ECONO Mode 81
- Function and Control 71 82
- 72 Function and Control 83
- 1.11 HOME LEAVE Operation 84
- 1.13 Other Functions 86
- 76 Function and Control 87
- 2.1 Main Structural Parts 88
- 2.2 Function of Thermistor 89
- Function and Control 79 90
- 2.2.2 Cooling Only Model 91
- Function and Control 81 92
- 3. Control Specification 93
- 3.2 Frequency Control 94
- Function and Control 85 96
- 3.3.1 Preheating Operation 97
- 3.3.4 3 Minutes Stand-by 97
- Function and Control 87 98
- 3.4 Discharge Pipe Control 99
- 3.5 Input Current Control 99
- 3.7 Heating Peak-cut Control 100
- 3.8 Fan Control 101
- 3.10 Defrost Control 102
- 92 Function and Control 103
- Function and Control 93 104
- 94 Function and Control 105
- 3.11.10 Oil Recovery Function 106
- 3.12 Malfunctions 107
- 3.13 Forced Operation Mode 108
- 3.14 Wiring-Error Check 109
- Function and Control 99 110
- 3.15 Additional Function 111
- COOL mode (C) 112
- HEAT mode (H) 112
- 5<C>3<H>1 112
- 102 Function and Control 113
- Operation Manual 114
- 1. System Configuration 115
- 2. Instruction 116
- Safety precautions 117
- Installation site 118
- Electrical work 118
- System relocation 118
- Names of parts 119
- Outdoor Unit 120
- Remote Controller 121
- Preparation Before Operation 137
- Receiver 138
- To set the clock 139
- Turn the breaker ON 139
- To start operation 140
- To stop operation 140
- Instruction SiBE12-713 141
- 130 Operation Manual 141
- To adjust the horizontal 142
- (louvers) 142
- 〈HEAT〉 The flap will go down 143
- To 3-D Airflow 147
- To cancel 3-D Airflow 147
- FTXG 25/35 E, CTXG 50 E 148
- POWERFUL Operation 152
- OUTDOOR UNIT QUIET Operation 153
- ECONO Operation 154
- HOME LEAVE Operation 155
- Useful in these cases 156
- INTELLIGENT EYE Operation 157
- Notes on “INTELLIGENT EYE” 160
- TIMER Operation 165
- To use ON TIMER operation 166
- Note for Multi System 167
- Fit the key 169
- [ Maintenance ] 170
- [ Replacement ] 170
- Before a long idle period 171
- Care and Cleaning 172
- Air Filter 173
- Cleaning the drain pan 182
- Trouble Shooting 188
- Check again 189
- Case Check 189
- Disposal requirements 190
- Fault diagnosis 191
- 190 Operation Manual 201
- To adjust the vertical 202
- Air flow selection 203
- ON TIMER OFF TIMER no setting 209
- WEEKLY TIMER Operation 210
- To cancel WEEKLY 211
- TIMER operation 211
- Setting WEEKLY TIMER 213
- ■ Priority Room Setting 215
- Place front 216
- Air filter 217
- Titanium Apatite 217
- Photocatalytic 217
- Air-Purifying 217
- TIMER CANCEL button 222
- It cancels the timer setting 222
- 2.3 FHQ Series 223
- 2. SAFETY CONSIDERATIONS 224
- 214 Operation Manual 225
- 3. OPERATION RANGE 226
- 4. INSTALLATION SITE 226
- NAME AND FUNCTION OF EACH 227
- AND DISPLAY ON THE 227
- REMOTE CONTROLLER 227
- 6. OPERATION PROCEDURE 228
- 218 Operation Manual 229
- 7. OPTIMUM OPERATION 230
- (FOR SERVICE PERSONNEL) 231
- CONDITIONER 232
- 222 Operation Manual 233
- 3PN05140-1V 234
- 224 Operation Manual 235
- Service Diagnosis 236
- 1. Caution for Diagnosis 237
- OPERATION lamp (green) 238
- 3. Service Check Function 240
- < ARC452A2 > 241
- 3.2 Check Method 2 242
- 232 Service Diagnosis 243
- 5. Troubleshooting 245
- 5.2 Outdoor Units 246
- SiBE12-713 Troubleshooting 248
- Service Diagnosis 237 248
- Troubleshooting SiBE12-713 249
- 238 Service Diagnosis 249
- 5.5.1 AC Motor 250
- 5.5.2 DC Motor 251
- Troubleshooting 252
- Check No.01 252
- Refer to P.276 252
- Check No.02 252
- 242 Service Diagnosis 253
- Service Diagnosis 243 254
- 244 Service Diagnosis 255
- Check No.10 256
- Refer to P.282 256
- 246 Service Diagnosis 257
- Service Diagnosis 247 258
- Check No.04 259
- Refer to P.277 259
- Check No.06 259
- Refer to P.279 259
- Service Diagnosis 249 260
- 250 Service Diagnosis 261
- 5.13 Compressor Lock 262
- 5.14 DC Fan Lock 263
- Service Diagnosis 253 264
- 254 Service Diagnosis 265
- Service Diagnosis 255 266
- 256 Service Diagnosis 267
- Service Diagnosis 257 268
- 258 Service Diagnosis 269
- 260 Service Diagnosis 271
- Service Diagnosis 261 272
- Check No.12 273
- Refer to P.283 273
- Service Diagnosis 263 274
- 264 Service Diagnosis 275
- Service Diagnosis 265 276
- Check No.07 277
- Refer to P.280 277
- Check No.09 277
- Refer to P.281 277
- Service Diagnosis 267 278
- Service Diagnosis 269 280
- 270 Service Diagnosis 281
- 5.25 Insufficient Gas 282
- Service Diagnosis 273 284
- 274 Service Diagnosis 285
- Service Diagnosis 275 286
- 6.1 How to Check 287
- Check No.05 289
- Check No.08 292
- Check SiBE12-713 293
- 282 Service Diagnosis 293
- 6.1.12 Power Transistor Check 294
- 284 Service Diagnosis 295
- 6.1.15 Hall IC Check 296
- 286 Service Diagnosis 297
- Removal Procedure 298
- 1. Outdoor Unit 299
- SiBE12-713 Outdoor Unit 302
- Removal Procedure 291 302
- Procedure Points 302
- Outdoor Unit SiBE12-713 303
- 292 Removal Procedure 303
- Removal Procedure 295 306
- 296 Removal Procedure 307
- Detach the outdoor air 309
- Loosen the screw on 309
- Loosen the 1 screw in 310
- Lift up the electrical box 310
- 1.3 Removal of the PCB 311
- 304 Removal Procedure 315
- Removal Procedure 305 316
- Lead wire Propeller fan 318
- Undo the fixing strings 322
- (body) and pull it out 322
- Open the sound blanket 322
- (inner) and pull it out 322
- Valve Coil and Thermistor 323
- 314 Removal Procedure 325
- Removal Procedure 315 326
- 1.9 Removal of the Compressor 328
- Others 319 330
- Others SiBE12-713 331
- 320 Others 331
- 1.2 Jumper Settings 332
- 322 Others 333
- Appendix 334
- 1.1 Indoor Units 335
- FTXS35D3VMW(L) 336
- FTXS35CAVMB 337
- 1.1.2 Duct Connected Type 338
- 1.1.4 Floor Standing Type 339
- 4D037995G 340
- 1.2.1 Cooling Only 341
- 1.2.2 Heat Pump 341
- 2. Wiring Diagrams 342
- 3D051268A 342
- 3D051652 342
- 3D033599G 343
- 3D038530N 343
- 3D050493 344
- 3D045012K 344
- 3D033909E 345
- 3D055953 345
- 3D037842D 346
- 3D055885 347
- 3D055495 347
- Index iii 350
- Drawings & Flow Charts 352
- SiBE 12-713 355
- Printed in Japan 03/2007 B AK 355
Related products and manuals for Split-system air conditioners Daikin FTKS60FV1B
(27 pages)
(9 pages)
(24 pages)© 2020, manymanuals.com. All rights reserved. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals