Daikin RXQ18P7W1BA Installation Manual Page 32
- Page / 38
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation manual
27
RX(Y)Q5-10-12P7W1B + RXQ8P7W1B + RXYQ8P8W1B +
RXYHQ12P8W1B + RX(Y)Q14~18P7W1BA
VRVIII System air conditioner
4PW48461-1
Setting mode 2
The H1P LED is on.
Setting procedure
1 Push the button according to the required function
(A~H). The LED indication that matches the required function is
shown below in the field marked :
2 When the button is pushed, the current setting is
defined.
3 Push the button according to the required setting
possibility as shown below in the field marked .
3.1 Possible settings for function A, B, C, G and H are (ON) or
(OFF).
3.2 Possible settings for function D
The noise of level 3 < level 2 < level 1 ( ).
3.3 Possible settings for function E and F
For function E
() only: the noise of level 3 < level 2
< level 1 ( ).
For function F () only: the power consumption of
level 1< level 2 < level 3 ( ).
4 Push the button and the setting is defined.
5 When the button is pushed again, the operation
starts according to the setting.
Refer to the service manual for more details and for other settings.
Confirmation of the set mode
The following items can be confirmed by setting mode 1 (H1P
LED is off)
Check the LED indication in the field marked .
1 Indication of the present operation state
- x, normal
- w, abnormal
- c, under preparation or under test operation
2 Indication of COOL/HEAT selection setting
3 Indication of low noise operation state
-
x standard operation (= factory setting)
- w operation
4 Indication of power consumption limitation setting
- x standard operation (= factory setting)
-
w operation
12.4. Test operation
Possible functions
A additional refrigerant charging operation.
B refrigerant recovery operation/vacuuming operation.
C setting of high static pressure.
D automatic low noise operation setting at nighttime.
E low noise operation level setting ( ) via the external
control adapter.
F power consumption limitation setting ( ) via the external
control adapter.
G enabling function of the low noise operation level setting
() and/or power consumption limitation setting
() via the external control adapter (DTA104A61/62).
H check operation (without initial refrigerant decision)
H1P H2P H3P H4P H5P H6P H7P
A
w x w x w x x
B
w x w x w x w
C
w x w x x w x
D
w x w x w w x
E
w x w w x x w
F
w x w w w w x
G
w x x w w x x
H
w x x x x w w
H1P H2P H3P H4P H5P H6P H7P
w xxxxc x
(a)
(a) This setting = factory setting
w xxxxx c
H1P H2P H3P H4P H5P H6P H7P
(a)
(a) This setting = factory setting
w xxxxx x
w xxxx
x c
w xxxx
c x
w xxxx
c c
H1P H2P H3P H4P H5P H6P H7P
w xxxx x c
(a)
(a) This setting = factory setting
w xxxx c x
w xxx
c x x
BS2 SET
L.N.O.P
DEMAND
L.N.O.P
DEMAND
BS3 RETURN
BS2 SET
ON
OFF
ON
OFF
1
OFF
1
2
3
L.N.O.P
1
DEMAND
3
1
2
3
H1P H2P H3P H4P H5P H6P H7P
x xwxxxx
1 When set to COOL/HEAT change-over by each individual outdoor
unit circuit (= factory setting).
2 Indication on master unit when COOL/HEAT change-over is
carried out by outdoor system connected in multiple system-
combination.
3 Indication on slave unit when COOL/HEAT change-over is carried
out by outdoor system connected in multiple system-combination.
H1P H2P H3P H4P H5P H6P H7P
1
(a)
(a) This setting = factory setting.
xxw x xxx
2
xxx w xxx
3
xxx x wx x
H1P H2P H3P H4P H5P H6P H7P
x xwx x xx
H1P H2P H3P H4P H5P H6P H7P
xxwxxxx
Do not insert fingers, rods or other objects into the air
inlet or outlet. When the fan is rotating at high speed, it
will cause injury.
Do not perform the test operation while working on the
indoor units.
When performing the test operation, not only the outdoor
unit, but the connected indoor unit will operate as well.
Working on a indoor unit while performing a test operation
is dangerous.
BS3 RETURN
BS3 RETURN
L.N.O.P
L.N.O.P
DEMAND
DEMAND
- INSTALLATION MANUAL 1
- A+B+C+D A+B 2
- >120 mm 3
- Daikin Europe N.V 4
- 2PW40200-8F 4
- Jiro Tomita 5
- Director Quality Assurance 5
- Ostend, 1st of October 2008 5
- CONTENTS Page 6
- NTRODUCTION 6
- 1.1. Combination 7
- AIN COMPONENTS 8
- ELECTION OF LOCATION 8
- NPACKING AND PLACING THE UNIT 9
- Model A B 9
- EFRIGERANT PIPING 10
- 6.1. Installation tools 10
- 6.3. Pipe connection 11
- Model A B C D 12
- VRVIII System air conditioner 13
- 4PW48461-1 13
- Installation manual 13
- 6.6. Example of connection 14
- EAK TEST AND VACUUM DRYING 16
- IELD WIRING 17
- 8.4. General cautions 19
- 8.5. System examples 20
- Sequential start 22
- Tightening torque (N•m) 22
- IPE INSULATION 23
- CONDITIONS 23
- HARGING REFRIGERANT 23
- H1P H2P H3P H4P H5P H6P H7P 25
- ■ Charging in cooling mode 27
- 3 Normal system display 29
- EFORE OPERATION 30
- 12.1. Service precautions 30
- 12.3. Field setting 30
- Setting mode 2 32
- Confirmation of the set mode 32
- 12.4. Test operation 32
- Normal completion 33
- Abnormal completion 33
- BS1 MODE 33
- BS4 TEST 33
- BS3 RETURN 33
- ERVICE MODE OPERATION 34
- AUTION FOR REFRIGERANT LEAKS 34
- ISPOSAL REQUIREMENTS 35
- NOTES NOTES 36
- Copyright © Daikin 38
Related products and manuals for Split-system air conditioners Daikin RXQ18P7W1BA
(34 pages)
(22 pages)
(18 pages)
(36 pages)© 2020, manymanuals.com. All rights reserved. | 2.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals