Daikin MC401VE Service Manual download pdf (Page 19)

Operation Manual SiENBE81-623A

18 Photocatalytic Air Purifiers

Preparation Before

Operation

! Installation of main unit

To install the unit, comply with the following standards to ensure performance.

If installed on a table

Min. 100cm

Airflow

Min. 50cm

Min. 10cm

Min. 50cm

ATTENTION

•

If operated outside the conditions shown below, malfunction may occur.

• Indoor temperature 0-32°C

• Indoor humidity 80% or less

How to Operate

1 When operating

Press the [ON/OFF] button.

Pressing again will stop.

2 When you want to automatically switch the airflow rate

Press the “ ” [AUTO] button.

• Automatically adjusts the airflow rate to “ ” LL (Quiet),

“ ” L (Low), “ ” M (Standard), “ ” H (high) in response to

the dirty condition of the air.

3 When you want to manually switch the airflow rate

Press the “ ” [FANSPEED] button.

• Each time it is pressed the airflow rate switches as shown below

allowing you to choose your desired flow.

“ ” “ ” “ ” “ ”

LL (Quiet) L (Low) M (

Standard

) H (High)

• The setting “ ” LL (Quiet) is a very slow airflow rate and is

convenient when sleeping.

• After setting “ ” LL (Quite) the power for cleaning the air

decresases because of the operation at slow airflow rate.

4 When you want to quickly clean the air

Press the “ ” [TURBO] button.

• A high airflow rate will quickly remove any dirtiness in the air.

• This is convenient to use when cleaning.

5 When you want to remove pollen

Press the “ ” [ANTI-POLLEN] button.

• Switching the airflow speed every 5 minutes between

“ ” M (Standard) and “ ” L (Low) will catch pollen before they

fall on the floor.

6 When you expel negative ions

Press the “ ” [RELAX] button.

Pressing again will cancel.

• Generates negative ions.

7 When you want to decide a time to stop operation

Press the “ ” [OFF TIMER] button.

• Each time it is pressed the timer setting switches as shown below.

The remaining time will be lit in the “OFF timer setting indicator”.

“ 1 ” (1 hour) “ 2 ” (2 hour) “ 4 ” (4 hour) (Cancel)

• When the set time is reached, the operation will automatically

stop.

• The set time can be changed if the button is pressed while the

timer is operating.

8 When you want to change the brightness of the

operation lamp and clean monitors

Press the “ ” [BRIGHTNESS] button.

• Each time it is pressed, the display will switch as shown below.

(Dark) (Off) (Standard)

9 When you want to prevent incorrect operation

Press the “ ” [LOCK] button for 2 seconds.

Pressing again for 2 seconds will cancel.

• Stops the function of the button other than the “ ” [LOCK]

button on the main unit and buttons on the remote control.

• This makes it possible to prevent children from operating the unit

incorrectly.

• When you want to release the child lock settings and the remote

controller is not in your hand, remove the power plug once and

then reinsert it and operate the unit.

! When you want to operate the unit using

the button on the main unit

When the remote control is not in your hand, you can use the

“ ” [Operation Switch / Stop] button on the main unit without using the

remote control. (page 4.)

NOTE

• The unit will not operate for 3 seconds after the front panel or

plasma ionizer is set or power plug is inserted even though

“” button on the remote control is pressed.

• Operation will stop for safety when the front panel is opened during

operation.

• When an incorrect operation is performed during operation

If the main unit display is abnormally on or remote control is

disabled due to thunder or radio transmission during operation, pull

the power plug and then re-insert it after 3 seconds.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 60 61

Comments to this Manuals

No comments

Daikin MC401VE Service Manual Page 19

Comments to this Manuals

Related products and manuals for Air filters Daikin MC401VE